Just How to Set up a Tub
Just How to Set up a Tub
Blog Article
How do you really feel when it comes to How to Install a Bathtub?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bath tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old tub with a new one is additionally a moderately challenging task. If the old tub is conveniently obtainable, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the job and also fit attempting it. As opposed to hiring a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This post will help you set up a brand-new bathtub in your shower room if you have already gotten a brand-new bathtub and do not need to alter the setup of your previous water system pipelines.
Your devices as well as material checklist ought to comprise the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to avoid strain on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be rather troublesome because of the restricted gain access to that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will come from the pipelines. Once the supply pipelines have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required placement. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub until the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Turn on the water supply and also examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and additionally examine the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the bathtub must wait up until the tub has actually been made use of at least when as this will certainly settle it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Secure the tap in place with the maker offered backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous kind must be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, bring about problems with dampness and possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and also can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Remember to always fill the bathtub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealer can break fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads on A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of writing was mandatory. Loved our post? Please share it. Let others discover it. Thank-you for your time spent reading it.
Get Quote
Report this page